Alaska 16 Hour Plumber CE Package

$199.00

This 16 hour package fulfills all state Continuing Education requirements for the 2 year renewal cycle for Alaska Plumbers .

  • 8 Hour Uniform Plumbing Code
  • 3 Hour Introduction to Fire Sprinklers, Valves, and Hydraulic Calculations
  • 3 Hour Confined Spaces
  • 2 Hour Pricing Plumbing for Profit

Description

Package Contents

  • 8 Hour Uniform Plumbing Code
  • 3 Hour Introduction to Fire Sprinklers, Valves, and Hydraulic Calculations
  • 3 Hour Confined Spaces
  • 2 Hour Pricing Plumbing for Profit

 


Uniform Plumbing Code 8HR CE


COURSE SYLLABUS

Course Description

This 8-hour continuing education course is designed to fulfill the code requirement for renewal of New Mexico Journeyman and Master plumbing licenses. Topics include code highlights from the Uniform Plumbing Code, outlined and explained by Master Plumber Lorren Schlotfelt in an easy to follow video format.


​Chapter 1 Administration – 30 minutes

  • Scope
  • Purpose
  • Existing Buildings
  • Additions, Alterations, Renovations and Repairs
  • Building Occupancy
  • Permits and Inspections
  • Violations

Chapter 2 Definitions – 50 minutes

  • Selected Definitions

Chapter 3 General Regulations – 30 minutes

  • Minimum Standards
  • Alternate Materials
  • Unlawful Practices
  • Prohibited Fittings and Practices
  • Independent Systems
  • Thermoplastic Pipe and Fittings

Chapter 4 Plumbing Fixtures and Fixture Fittings – 30 minutes

  • Quality
  • Setting
  • Design and Installation of Plumbing Fixtures
  • Water and Waste Connections
  • Flow Rates
  • Shower Receptors
  • Water Closets
  • Backflow Protection
  • Floor Drains

Chapter 5 Water Heaters – 50 minutes

  • Applicability
  • Other Types
  • Air Infiltration Rate Method
  • Installation
  • Chimneys and Venting
  • Termination
  • Vent Downsizing

Chapter 6 Water Supply and Distribution – 60 minutes

  • Potable/Non-Potable Water
  • Alternate Water Systems
  • Vacuum Breakers/Backflow Prevention
  • Dispensers
  • Materials
  • Fittings
  • Joints
  • Water Pressure
  • Sizing
  • Sprinklers

Chapter 7 Sanitary Drainage – 50 minutes

  • Piping
  • Number of Fixture Units
  • Joints and Connections
  • Cleanouts
  • Building Drains and Sewers

Chapter 8 Indirect Waste – 10 minutes

  • Food and Beverage Establishments
  • Pipe Size and Length
  • Chemical Wastes

Chapter 9 Vents – 30 minutes

  • Siphonage/Back Pressure/Air Circulation
  • Materials
  • Termination
  • Flow Characteristics
  • Wet Venting
  • Combination Waste and Vent Systems
  • Circuit Venting

Chapter 10 Traps and Interceptors – 15 minutes

  • Types
  • Seals/Seal Protection
  • Grease Interceptors

Chapter 11 Storm Drainage – 15 minutes

  • Methods
  • Sumps
  • Drains
  • Secondary Drains
  • Combined Systems
  • Leaders, Conductors and Storm Drains

Appendices – 60 minutes

  • Appendix A Rules for Sizing Water Supply Systems
  • Appendix B Explanatory Notes on Combination Waste and Vent Systems
  • Appendix C Alternate Plumbing Systems
  • Appendix H Private Sewage Disposal Systems
  • Appendix I Installation for PEX Tubing
  • Appendix K Potable Rainwater Catchment Systems
  • Appendix L Sustainable Practices

Introduction to Fire Sprinklers, Valves, and Hydraulic Calculations
3HR CE


Course Description

This course is an introduction to the basics regarding fire sprinklers, valves and hydraulic calculations. Students will become familiar with the parts of a sprinkler assembly and the significance of sprinkler orientation. Next they will learn the basics of sprinkler system valves and the types of systems they service. Finally, hydraulic calculations are discussed as they relate to water supply, water flow and friction loss.


Chapter 1 – Sprinklers

Lesson 1

  • Sprinkler basics
  • Parts of the sprinkler

Lesson 2

  • Sprinkler orientation
  • Types of sprinklers

Chapter 2 – Valves

Lesson 1

  • Types of valves
  • Types of sprinkler systems

Lesson 2 

  • Types of sprinkler systems cont.

Lesson 3

  • Setting air pressure
  • Water delivery

Chapter 3 – Hydraulic Calculations

Lesson 1

  • Water pressure
  • Water supply and flow
  • Friction loss

Lesson 2

  • Internal pipe diameter
  • Examples of calculations

Confined Spaces 3HR CE


COURSE SYLLABUS

Course Description

29 CFR 1926 – Subpart AA Confined Spaces in Construction sets forth requirements for practices and procedures to protect employees engaged in construction activities at a worksite with one or more confined spaces. Examples of locations where confined spaces may occur include, but are not limited to, the following: Bins; boilers; pits (such as elevator, escalator, pump, valve or other equipment); manholes (such as sewer, storm drain, electrical, communication, or other utility); tanks (such as fuel, chemical, water, or other liquid, solid or gas); incinerators; scrubbers; concrete pier columns; sewers; transformer vaults; heating, ventilation, and air-conditioning (HVAC) ducts; storm drains; water mains; precast concrete and other pre-formed manhole units; drilled shafts; enclosed beams; vessels; digesters; lift stations; cesspools; silos; air receivers; sludge gates; air preheaters; step up transformers; turbines; chillers; bag houses; and/or mixers/reactors.


 

29 CFR 1926 – Subpart AA
Confined Spaces in Construction

Lesson 1 – 35 minutes

  • 1926.1201 Scope
  • 1926.1202 Definitions

Lesson 2 – 30 minutes

  • 1926.1203 General Requirements

Lesson 3 – 30 minutes

  • 1926.1204 Permit-required Confined Space Program
  • 1926.1205 Permitting Process
  • 1926.1206 Entry Permit

Lesson 4 – 35 minutes

  • 1926.1207 Training
  • 1926.1208 Duties of Authorized Entrants
  • 1926.1209 Duties of Attendants
  • 1926.1210 Duties of Entry Supervisors
  • 1926.1211 Rescue and Emergency Services
  • 1926.1212 Employee Participation
  • 1926.1213 Provision of Documents to Secretary

 


Pricing Plumbing for Profit


Course Description

Stop flushing money! This video course is designed to help anyone who is either thinking of starting up their own plumbing business, or who wants to be confident that they will operate at a profit. In this step-by-step tutorial, you will learn how to accurately account for all your costs, and then apply those costs to an estimate. Running a successful plumbing business requires careful attention to detail by accounting for all costs associated with the business, and charging the customer enough to make a profit. Downloadable worksheets that you can customize to your own business are included!


Cost Workbook – 55 minutes

Page One

  • Employee Costs
  • Office Costs
  • Vehicle Costs
  • Marketing Costs
  • Clothing/Misc. Expenses
  • Training Costs

Page Two

  • Calculations:
    • Hours worked per year
    • Break even rate
    • Profit margins

Estimating Worksheet – 45 minutes

  • Materials
  • Labor

Course instructors will be available by email or telephone between 8am and 6pm Eastern Standard Time. They will assist you with questions regarding course content.

If you have any questions, please call us at 1-800-727-7104 or send an email to info@onlinecti.com. Email responses will usually be returned promptly, but guaranteed within one business day.

Student policies and procedures are always available by going to our website and scrolling to the bottom of the page (See Attendance, Privacy and Refund Policy).