- 4 Hour Uniform Plumbing Code Chapters 6-9 and Apendices
- 3 Hour Confined Spaces
- 1 Hour Plan Reading
ID Uniform Plumbing Code Chapters 6-9 and Appendices
This 4-hour continuing education course is designed to fulfill the code requirement for renewal of Idaho plumbing licenses. Topics include code highlights from the Uniform Plumbing Code, Chapter 6-9 and includes a review of the Appendices, outlined and explained by Master Plumber Lorren Schlotfelt in an easy to follow video format.
Chapter 6 Water Supply and Distribution – 60 minutes
- Potable/Non-Potable Water
- Alternate Water Systems
- Vacuum Breakers/Backflow Prevention
- Water Pressure
Chapter 7 Sanitary Drainage – 50 minutes
- Number of Fixture Units
- Joints and Connections
- Building Drains and Sewers
Chapter 8 Indirect Waste – 10 minutes
- Food and Beverage Establishments
- Pipe Size and Length
- Chemical Wastes
Chapter 9 Vents – 30 minutes
- Siphonage/Back Pressure/Air Circulation
- Flow Characteristics
- Wet Venting
- Combination Waste and Vent Systems
- Circuit Venting
Appendices – 60 minutes
- Appendix A Rules for Sizing Water Supply Systems
- Appendix B Explanatory Notes on Combination Waste and Vent Systems
- Appendix C Alternate Plumbing Systems
- Appendix H Private Sewage Disposal Systems
- Appendix I Installation for PEX Tubing
- Appendix K Potable Rainwater Catchment Systems
- Appendix L Sustainable Practices
- Appendix M Peak Water Demand Calculator
Confined Spaces 3HR CE
29 CFR 1926 – Subpart AA Confined Spaces in Construction sets forth requirements for practices and procedures to protect employees engaged in construction activities at a worksite with one or more confined spaces. Examples of locations where confined spaces may occur include, but are not limited to, the following: Bins; boilers; pits (such as elevator, escalator, pump, valve or other equipment); manholes (such as sewer, storm drain, electrical, communication, or other utility); tanks (such as fuel, chemical, water, or other liquid, solid or gas); incinerators; scrubbers; concrete pier columns; sewers; transformer vaults; heating, ventilation, and air-conditioning (HVAC) ducts; storm drains; water mains; precast concrete and other pre-formed manhole units; drilled shafts; enclosed beams; vessels; digesters; lift stations; cesspools; silos; air receivers; sludge gates; air preheaters; step up transformers; turbines; chillers; bag houses; and/or mixers/reactors.
29 CFR 1926 – Subpart AA
Confined Spaces in Construction
Lesson 1 – 35 minutes
- 1926.1201 Scope
- 1926.1202 Definitions
Lesson 2 – 30 minutes
- 1926.1203 General Requirements
Lesson 3 – 30 minutes
- 1926.1204 Permit-required Confined Space Program
- 1926.1205 Permitting Process
- 1926.1206 Entry Permit
Lesson 4 – 35 minutes
- 1926.1207 Training
- 1926.1208 Duties of Authorized Entrants
- 1926.1209 Duties of Attendants
- 1926.1210 Duties of Entry Supervisors
- 1926.1211 Rescue and Emergency Services
- 1926.1212 Employee Participation
- 1926.1213 Provision of Documents to Secretary
Final Assessment – 20 minutes
1HR Plan Reading CE
The ability to interpret plumbing blueprints and successfully install the required plumbing systems is an essential skill. Prints provide the details you need regarding types and sizes of sinks to the location of gas lines, drains and vents. This video course outlines the general layout of both residential and commercial plans, identifying and detailing schedules, legends, symbols and engineering instructions.
At the end of this course participants will be able to:
- Identify the various symbols included in any residential or commercial blueprint.
- Gain a broad understanding of the methodology behind successful plan reading.
- Detail and implement the use of blueprints when bidding and completing a plumbing project.
Lesson 1 Details of Engineered Prints – 17 minutes: This lesson is an introduction to plan reading basics, and how to interpret the general information found on the main page of the print.
- Commercial plan
Lesson 2 Details of Engineered Prints (cont.) – 25 minutes: This lesson looks at the plumbing pages of the print, information that is specific to the work required of the plumber.
- Plumbing floor plan
- Symbols and abbreviations
- Mechanical plan
Lesson 3 Details of Engineered Prints (cont.) – 25 minutes: This lesson outlines using blueprints for a residential home.
- Residential plan
Course instructors will be available by email or telephone between 8am and 6pm Eastern Standard Time. They will assist you with questions regarding course content.
If you have any questions, please call us at 1-800-727-7104 or send an email to firstname.lastname@example.org. Email responses will usually be returned promptly, but guaranteed within one business day.
Student policies and procedures are always available by going to our website and scrolling to the bottom of the page (See Attendance, Privacy and Refund Policy).