Description
PACKAGE CONTENTS:
- Wyoming ICC Journeyman Plumber Exam Prep Course
- International Fuel and Gas Code Exam Prep Course
- International Plumbing Code 2015
- International Fuel Gas Code 2015
- Pre-printed tabs for both books
Wyoming Journeyman Plumber Exam Prep Course
COURSE SYLLABUS
Course Description
This easy to follow video training program will prepare you to pass the plumbing exam. The course is based on the International Plumbing Code (IPC), along with Wyoming state specific amendments, laws, and rules. This course will teach you how to find answers quickly and efficiently in the code book, which is crucial for passing the exam.
Also included in this course is an in-depth lesson on basic isometric drawings, a hands-on copper soldering demonstration, basic and advanced plumbing math, and hundreds of practice questions and problems.
PLUMBING EXAM PREP SYLLABUS
1. About the Exam
- Reading and Understanding the PSI Bulletin
- Books That You Should Have During the Exam
- Effective Study Techniques
2. Introduction
3. IPC Chapter 1 Administration, Scope and Intent/Purpose
4. IPC Chapter 2 – Definitions and Symbols
- Study Techniques
- Definitions
5. Plumbing Math
- Constants/Conversions/Volume
- Offsets/Slope/Practice problems
6. IPC Chapter 3 – General Regulations
7. IPC Chapter 4 – Fixtures, Faucets, and Fixture Fittings
- Code overview
- Practice problems
8. IPC Chapter 5 – Water Heaters
- Overview
9. IPC Chapter 6 – Water Supply and Distribution
- Water Distribution
- Potable Water Supply
- Backflow Prevention
10. IPC Chapter 7 – Sanitary Drainage
- Drainage
- Cleanouts
- Fixture Units
11. IPC Chapter 8 – Indirect and Special Waste
- Requirements
12. IPC Chapter 9 – Vents
- Materials
- Vent Extensions, Connections and Grades
- Pipe Sizing, Developed Length
- Stack Offsets, Branches
- Fixture Vents
- Wet Vents
- Stack Vents
- Circuit Vents
- Admittance Valves
13. IPC Chapter 10 – Traps, Interceptors and Separators
- Requirements
14. IPC Chapter 11 – Storm Drainage
- Area, Volume and Drainage Practice Problems
- Sizing Methods
- Secondary Drains
15. IPC Chapter 13 – Nonpotable Water Systems
- Reclaimed vs. Potable
- Requirements
- Problems
16. IPC Chapter 14 – Subsurface Landscape Irrigation Systems
- System Design and Sizing
- Installation
17. Appendix E
- Sizing of Water Piping Systems
- Friction Charts and Lengths
18. Isometrics
- Basic Layout
- Practice Problems
19. Private Sewage Systems
- Soil Absorption Systems
- Tank Sizing
20. International Fuel Gas Code
- General Overview
21. Hands-On Practical Application
- Measuring, fitting, and soldering copper piping
22. Practice Test
- Hundreds of practice questions
International Fuel and Gas Code
Course Description
The International Fuel Gas Code® (IFGC®) establishes minimum requirements for plumbing systems using prescriptive and performance-related provisions. It is founded on broad-based principles that make possible the use of new materials and new plumbing designs. This course will review the basic provisions for appliance installation, combustion air, venting, fuel gas piping, ducting, ventilation and exhaust. Participants will gain an understanding how these requirements apply to design, plan review and inspection
Chapter 1 Scope and Administration
- Applicability
- Permits
- Inspections
- Violations
Chapter 2 Definitions
- Definitions
Chapter 3 General Regulations
- Structural Safety
- Appliance Location
- Combustion, Ventilation and Dilution Air
- Installation
- Access and Service Space
- Condensate Disposal
- Clearance Reduction
- Electrical
Chapter 4 Gas Piping Installations
- Pipe Sizing
- Piping Materials
- System Installation
- Appliance and Manufactured Home Connections
- Piping Support Intervals
- Overpressure Protection Devices
Chapter 5 Chimneys and Vents
- Vents
- Venting of Appliances
- Sizing of Category 1 Appliance Venting Systems
Chapter 6 Specific Appliances
- Forced-Air Warm-Air Furnaces
- Gas-Fired Toilets
- Boilers
- Chimney Damper Opening Area
Chapter 7 Gaseous Hydrogen Systems
- General Definitions
- Appendix A – Sizing and Capacities of Gas Piping
- Appendix B – Sizing of Venting Systems
- Appendix C – Exit Terminals
- Appendix D – Safety Inspections
Course instructors will be available by email or telephone between 9am and 5pm Eastern Standard Time. They will assist you with questions regarding course content.
If you have any questions, please call us at 1-800-727-7104 or send an email to info@onlinecti.com. Email responses will usually be returned promptly, but guaranteed within one business day.
Student policies and procedures are always available by going to our website and scrolling to the bottom of the page (See Attendance and Privacy Policy).